SEM206P Temperature Transmitter for Pt100 Sensors – PC Programmable

£51.50

The SEM206P is our entry-level PC programmable in head temperature transmitter. It accepts Pt100 temperature sensors and converts the sensor output to a standard industrial 4 to 20mA transmission signal. Delivery available from stock.

Transmitter Range

Clear

SEM206P Temperature Transmitter for Pt100 Sensors – PC Programmable

SKU: N/A Category: Temperature Transmitters

QUANTITY DISCOUNTs: 1-9 = 0% 10-19 = 5% 20+ = 10%

PC configuration allows the user to select the range, units and burnout direction, without requiring calibration equipment. Configuration is performed quickly using our new USB port driven configurator by simply connecting two clips to the SEM206P loop terminals and following the software instructions. Calibration set up may be saved as a file on the PC for later use.

However, if you already know the temperature range you require, we can configure the product for you at no extra cost.

Looking for a transmitter with Thermocouple input? See our SEM206TC.

Data Sheet

Transmitter Range	0 to 100°C (Default), -25 to +75°C, 0 to 150°C, 0 to 200°C, -50 to +250°C, Custom – We will contact you

Features

Suitable For Pt100 Sensors
High stability
Over range LED indication
Programmable burnout
Gost Certificate
Sine Vibration Certificate
Can be supplied fitted to our temperature sensors.

General Specification

Update time:	500 ms.
Response Time:	1 second
Start up time:	4 seconds ( I out < 4 mA during start up)
Warm-up time:	1 minute to full accuracy
Power Supply :	10 to 30 Volts dc
Ambient operating range:	-40 to +85°C [Full Accuracy only between -30 to +75°C].
Ambient storage temperature:	-50 to +90°C.
Ambient humidity range:	10 to 90% RH non condensing
Dimensions:	43 mm diameter; 21 mm height.
Weight:	31 g (encapsulated).
APPROVALS:
EMC – BS EN 61326:	Electrical equipment for measurement control and laboratory use.
ANNEX A:	Immunity test requirements for equipment intended for use in industrial locations
ANNEX F:	Test configurations, operational conditions and performance criteria for transducers with integrated or remote signal conditioning.
IEC 61000-4-2:	Electrostatic discharge
IEC 61000-4-3:	EM Field
IEC 61000-4-4:	Transient Burst (output)
IEC 61000-4-5:	Surge (output).

Note – Sensor input wires to be less than 3 metres to comply.

Specifications @ 20°C State

INPUT:
Sensor Type:	Pt100 100R @ 0°C 2 or 3 Wire.
Sensor Range :	-195 to +845°C (18 to 390Ω)
Sensor Connection:	Screw terminal
*Minimum span (1) :**	25 °C
Linearisation:	BS EN 60751(IEC 751) standard / JISC 1604
*Measurement Accuracy (2) :**	0.2 °C ± 0.05 % of Reading.
Thermal Drift:	±0.02 °C / °C.
Excitation current:
Lead Resistance effect:	0.002 °C / Ohm.
Maximum lead Resistance:	20 Ohms per leg.
OUTPUT:
Output Type:	2 wire, 4 to 20mA current loop.
Output range:	4.0 to 20.0mA
Output Connection :	Screw terminal
Maximum output:	21.5mA (in high burnout condition)
Minimum output:
Accuracy:	(mA output /2000) or 5 uA (Which ever is the greater)
Loop Voltage effect:	0.2 uA / V.
Thermal drift:	±2 uA / °C
Maximum output load:	[(Vsupply-10)/21]K Ohms (Example: 700 Ohms @ 24V)